| View previous topic :: View next topic |
| Author |
Message |
Jai_Guru
Joined: 13 Aug 2006
Posts: 12
|
 Posted: Mon Jan 15, 2007 6:55 pm Post subject: PSP Oscilloscope |
 |
|
I would like to use my PSP as an oscilloscope by connecting the input voltage to the analog audio input. The main use of this would be to make measurements on micro controller circuits with TTL voltage levels (6V-0V).
Does somebody know what is the range of voltages supported by the audio input?
Has somebody developed something similar? |
|
| Back to top |
|
 |
MrMr[iCE]
Joined: 03 Oct 2005
Posts: 43
|
| Posted: Tue Jan 16, 2007 4:11 pm Post subject: |
|
|
| I think your 'scope' would be limited to sampling at 44kz, the only frequency it can record at (I think, someone correct me if I'm wrong). You'd need something a bit more realtime, possibly through the usb port. |
|
| Back to top |
|
|
Jai_Guru
Joined: 13 Aug 2006
Posts: 12
|
| Posted: Tue Jan 16, 2007 4:53 pm Post subject: |
|
|
I'm not sure about USB, hardwarewise it gets much more complicated.
My aim is to analyze the signals sent by a keyboard, pulses sent to a servo motor to control it or maybe signals sent on serial communication.
This signals operate at frequencies lower than 44kz so I don't think this would be a problem. |
|
| Back to top |
|
|
Jai_Guru
Joined: 13 Aug 2006
Posts: 12
|
| Posted: Wed Jan 31, 2007 4:33 pm Post subject: |
|
|
| What circuit do I need to build to connect 5v TTL signals to the audio input of my PSP and not ruin it? |
|
| Back to top |
|
|
avisx
Joined: 09 Dec 2006
Posts: 8
|
| Posted: Wed Jan 31, 2007 10:06 pm Post subject: good idea |
|
|
| good idea, ;) |
|
| Back to top |
|
|
memon
Joined: 03 Oct 2005
Posts: 63
|
| Posted: Wed Jan 31, 2007 10:39 pm Post subject: |
|
|
There are some projects around the web which purpose is to turn a pc sound card into a oscilloscope. Google: pc sound card oscilloscope
You will need some special electronics to convert the signal to nice range for the sound card (or psp) to record. You will run into a problem trying to measure DC voltages, though, because there is usually a capacitor in the input before the ADC.
This might be a good starting point:
http://xoscope.sourceforge.net/ |
|
| Back to top |
|
|
Jai_Guru
Joined: 13 Aug 2006
Posts: 12
|
| Posted: Thu Feb 01, 2007 3:07 am Post subject: |
|
|
Thanks for the reply.
Sorry, but i'm not very experienced with hardware.
| Quote: | | You will run into a problem trying to measure DC voltages, though, because there is usually a capacitor in the input before the ADC. |
As I said before, the main use i want to give this is to measure signals from microlcontrolers so I need to measure DC voltages.
To fix this could I modulate the input signal somehow and then demodulated using software? |
|
| Back to top |
|
|
Jai_Guru
Joined: 13 Aug 2006
Posts: 12
|
| Posted: Thu Feb 01, 2007 4:34 pm Post subject: |
|
|
I found this page that could be useful.
http://www.qsl.net/om3cph/sb/dcwithsb.htm
It explains the problems of using a sound card to measure DC signals. I haven't finished reading it but it looks like a valuable resource. |
|
| Back to top |
|
|
Jai_Guru
Joined: 13 Aug 2006
Posts: 12
|
| Posted: Thu Feb 01, 2007 5:34 pm Post subject: |
|
|
My next question will be a bit off topic but I hope it's not a big problem.
I found an old sound card and I wonder if I could avoid the DC measuring problem by removing and bypassing the capacitors right next to the line in and mic plug.
Any opinions? |
|
| Back to top |
|
|
Jai_Guru
Joined: 13 Aug 2006
Posts: 12
|
| Posted: Sat Feb 03, 2007 3:11 am Post subject: |
|
|
I think what a want it's not an Oscilloscope but a logic analyzer.
I'm only interested on binary voltage levels.
Is there a way to know if a pin on USB or Serial Port is high or low?
what other method of input could be used? |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
